Microsoft LPF-00004 Manual del operador Pagina 95
- Pagina / 157
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CMD300 CONTROL SOFTWARE Page 77
C
YBER
A
MP
380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.
33)
STEP
This command sets the program into step-by-step command-file mode. This command could
be used both on the command line and in a command file to switch the command file
processing into step-by-step mode. In the example below, if the following command file
EXAMP.CMD is being processed continuously, then it will switch to step mode at line 3.
CHANNEL 1-4
GAIN 10
STEP
CHANNEL 5-8
GAIN 50
The following command causes CMD300 to continuously process the command file until line
3 and then await user input.
CMD300 @EXAMP
The pause at line 3 might allow the user to adjust equipment, and then to manually issue the
CONTINUOUS command to resume processing of the command file.
34)
UPDATE
This command writes the current CyberAmp settings to the main CyberAmp EEPROM. This
command is usually not required because CMD300 automatically updates settings as they are
changed.
35)
V
ERIFY
or
VERIFY PROBE <probe number>
VERIFY directs the CyberAmp to run a verification test on its own main system. If the main
system unit is functioning normally, then the program will display a message of the form:
RAM OK
EEPROM OK
OFFSETS
1=+00012
2=+00003
3=+00045
4=+00006
5=+00070
6=+00004
7=+00210
8=+09100
Note that all channel offsets should have a value less than 1000 (equivalent to 100 mV). As
displayed, channel 8 is suspect because it has an offset of 910.0 mV.
VERIFY PROBE directs the CyberAmp to check the probe EEPROM. The message
EEPROM OK is displayed if verification is successful.
- CyberAmp 380 1
- Declaration of Conformity 3
- IMPORTANT INFORMATION 5
- RENSEIGNMENTS IMPORTANTS 6
- WICHTIGE INFORMATIONEN 7
- INFORMACION IMPORTANTE 8
- Explanation of symbols 9
- Explication des symboles 9
- Explicación de símbolos 9
- SÉCURITÉ 10
- SICHERHEITS 10
- HINWEISE 10
- SEGURIDAD 10
- COPYRIGHT 11
- VERIFICATION 11
- TABLE OF CONTENTS 13
- INTRODUCTION 19
- Page 2 INTRODUCTION 20
- INTRODUCTION Page 3 21
- FUNCTIONAL DESCRIPTION 23
- General Features 26
- FUNCTIONAL CHECKOUT 29
- TYPICAL CONFIGURATIONS 33
- Supply Voltage 37
- Changing the Fuse 37
- Grounding and Hum 38
- Power-Supply Glitches 39
- Input Coupling 39
- Expansion 40
- Low-Pass Filter 41
- Amplitude Characteristics 42
- Sampling Rate 43
- 10-90% Rise Time 43
- AC Coupling and Autozeroing 44
- 3 dB frequency of 44
- Time Constant 46
- 100 1.6 46
- Saturation 47
- Notch Filter 48
- Overload Detection 49
- Audio Monitor 50
- External Input 51
- Electrode Test 52
- Strain Gauges 55
- Active Probes 56
- Common-Mode Rejection Ratio 57
- Troubleshooting 59
- TRANSDUCERS 61
- Page 44 TRANSDUCERS 62
- TRANSDUCERS Page 45 63
- EMG, EEG, ECG Recording 64
- Nerve Cuffs 65
- Metal Microelectrodes 65
- Page 48 TRANSDUCERS 66
- Pressure 67
- Acceleration 67
- Self Heating 68
- Isolation 68
- Insulation Techniques 68
- AI 400 SERIES SmartProbes 69
- Transducer Adapter 71
- Input Connector Color Scheme 72
- Recommended Input Coupling 73
- Connector 74
- Example Circuits 75
- Basic Thermistor Circuit 76
- Amplifier Probes 78
- Current Probes 79
- Photodiode Amplifier 79
- Linear Potentiometers 80
- Rotary Potentiometers 80
- Panel Switch 81
- Foot Switch 81
- CMD300 CONTROL SOFTWARE 83
- Command-Line Mode 85
- Interactive Mode 85
- Command-File Mode 86
- Command Reference 87
- CMD300 OVERLOAD 91
- CMD300 REPEAT OVERLOAD 94
- QUICK300 CONTROL SOFTWARE 97
- Command Line Options 100
- CyberControl SOFTWARE 101
- Starting CyberControl 102
- Overload Handling 105
- Keyboard Commands 105
- Communications Settings 107
- PC Menus 108
- Macintosh Menus 109
- PROGRAMMER'S GUIDE 112
- Libraries and Example Code 114
- > end of response 116
- AT3F5 24000 118
- 2 4 6 8 10 ... 28000 30000 118
- AT8R06000 121
- D5=-1234500 124
- Implementation Notes 125
- Support Routine Details 125
- Example Programs 129
- SPECIFICATIONS 135
- Page 118 SPECIFICATIONS 136
- Offset range: ±10 V 137
- Page 120 SPECIFICATIONS 138
- SPECIFICATIONS Page 121 139
- Page 122 SPECIFICATIONS 140
- REFERENCES 141
- ADJUSTMENT PROCEDURES 143
- Other Adjustments 144
- CIRCUIT DIAGRAMS Page 127 145
- SERIAL COMMUNICATIONS CABLES 147
- LIST OF FIGURES AND TABLES 149
- WARRANTY 151
- WARNING 153
- INDEX Page 137 155
Relacionado con productos y manuales para De medición, control y control Microsoft LPF-00004
(82 paginas)Panasonic HCV707MEG manuales
Manuales del propietario y guías del usuario para No Panasonic HCV707MEG.
Ofrecemos 1 manuales en pdf Panasonic HCV707MEG para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales