Microsoft LPF-00004 Manual del operador Pagina 91
- Pagina / 157
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CMD300 CONTROL SOFTWARE Page 73
C
YBER
A
MP
380, COPYRIGHT MARCH 2002, AXON INSTRUMENTS, INC.
12)
O
FFSET <offset value>
The OFFSET command specifies the DC offset adjustment that is added after the pre-filter
gain amplifier. The <offset value> is specified in millivolts and can be in the range -3000.0 to
+3000.0 mV. Because this offset is introduced after the pre-filter gain amplifier, the input-
referred offset value depends on the gain setting of the pre-filter amplifier.
13)
OV
ERLOAD
OVERLOAD commands the CyberAmp to report which channels have overloaded since the
last time that this command was issued or since the unit was powered up. After the report, the
CyberAmps resets the overload status for all channels. The following response indicates that
channels 1, 3, 4 and 7 have overloaded since the last check.
CMD300 OVERLOAD
CyberAmp overload status: 1, -, 3, 4, -, -, 7, -
14)
PO
STGAIN <output gain value>
This command sets the output gain amplifier for the selected channels without changing the
pre-filter gain amplifier. Allowable values for <output gain value> are:
1, 2, 5, 10, 20, 50, 100 and 200.
15)
PR
EGAIN <pre-filter gain value>
This command sets the pre-filter gain amplifier for the selected channels without changing the
output gain amplifier. Allowable values for <pre-filter gain value> are:
1, 10 and 100.
16)
QUIET
This command minimizes all subsequent CyberAmp responses to commands. In QUIET
mode no confirmation is given for simple commands such as changes to gain or filter settings.
CyberAmp responses are maximized with the VERBOSE Command.
17)
STATUS
or
STATUS DEFAULTS
or
STATUS ID
The STATUS command displays the CyberAmp unit type, serial number, firmware revision
number, and status information for all channels. The format of the channel status information
is as follows:
#1 Pr=AI401 +=DC -=Gnd Gain=20(10,2) Filt=10k Notch=N Offset=+50mV
- CyberAmp 380 1
- Declaration of Conformity 3
- IMPORTANT INFORMATION 5
- RENSEIGNMENTS IMPORTANTS 6
- WICHTIGE INFORMATIONEN 7
- INFORMACION IMPORTANTE 8
- Explanation of symbols 9
- Explication des symboles 9
- Explicación de símbolos 9
- SÉCURITÉ 10
- SICHERHEITS 10
- HINWEISE 10
- SEGURIDAD 10
- COPYRIGHT 11
- VERIFICATION 11
- TABLE OF CONTENTS 13
- INTRODUCTION 19
- Page 2 INTRODUCTION 20
- INTRODUCTION Page 3 21
- FUNCTIONAL DESCRIPTION 23
- General Features 26
- FUNCTIONAL CHECKOUT 29
- TYPICAL CONFIGURATIONS 33
- Supply Voltage 37
- Changing the Fuse 37
- Grounding and Hum 38
- Power-Supply Glitches 39
- Input Coupling 39
- Expansion 40
- Low-Pass Filter 41
- Amplitude Characteristics 42
- Sampling Rate 43
- 10-90% Rise Time 43
- AC Coupling and Autozeroing 44
- 3 dB frequency of 44
- Time Constant 46
- 100 1.6 46
- Saturation 47
- Notch Filter 48
- Overload Detection 49
- Audio Monitor 50
- External Input 51
- Electrode Test 52
- Strain Gauges 55
- Active Probes 56
- Common-Mode Rejection Ratio 57
- Troubleshooting 59
- TRANSDUCERS 61
- Page 44 TRANSDUCERS 62
- TRANSDUCERS Page 45 63
- EMG, EEG, ECG Recording 64
- Nerve Cuffs 65
- Metal Microelectrodes 65
- Page 48 TRANSDUCERS 66
- Pressure 67
- Acceleration 67
- Self Heating 68
- Isolation 68
- Insulation Techniques 68
- AI 400 SERIES SmartProbes 69
- Transducer Adapter 71
- Input Connector Color Scheme 72
- Recommended Input Coupling 73
- Connector 74
- Example Circuits 75
- Basic Thermistor Circuit 76
- Amplifier Probes 78
- Current Probes 79
- Photodiode Amplifier 79
- Linear Potentiometers 80
- Rotary Potentiometers 80
- Panel Switch 81
- Foot Switch 81
- CMD300 CONTROL SOFTWARE 83
- Command-Line Mode 85
- Interactive Mode 85
- Command-File Mode 86
- Command Reference 87
- CMD300 OVERLOAD 91
- CMD300 REPEAT OVERLOAD 94
- QUICK300 CONTROL SOFTWARE 97
- Command Line Options 100
- CyberControl SOFTWARE 101
- Starting CyberControl 102
- Overload Handling 105
- Keyboard Commands 105
- Communications Settings 107
- PC Menus 108
- Macintosh Menus 109
- PROGRAMMER'S GUIDE 112
- Libraries and Example Code 114
- > end of response 116
- AT3F5 24000 118
- 2 4 6 8 10 ... 28000 30000 118
- AT8R06000 121
- D5=-1234500 124
- Implementation Notes 125
- Support Routine Details 125
- Example Programs 129
- SPECIFICATIONS 135
- Page 118 SPECIFICATIONS 136
- Offset range: ±10 V 137
- Page 120 SPECIFICATIONS 138
- SPECIFICATIONS Page 121 139
- Page 122 SPECIFICATIONS 140
- REFERENCES 141
- ADJUSTMENT PROCEDURES 143
- Other Adjustments 144
- CIRCUIT DIAGRAMS Page 127 145
- SERIAL COMMUNICATIONS CABLES 147
- LIST OF FIGURES AND TABLES 149
- WARRANTY 151
- WARNING 153
- INDEX Page 137 155
Relacionado con productos y manuales para De medición, control y control Microsoft LPF-00004
(82 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales