Microsoft RAMCard C-97200 Manual de usuario descargar pdf (Pagina 10)

Analog Output Interface

(Cat. No. 206-69240)

・

Outputs voltage signals proportional to

the fluorescence intensity.

・

Specifications

Resolution: 18 bits

Output: 1 V/FS, 100 mV/FS

ASC-5Auto Sample Changer

(Cat. No. 204-09100)

・

Builds an automatic multisample

spectrophotometry system in

combination with a sipper unit.

・

The aspirating nozzle is programmable

to move in the X, Y, and Z (vertical)

directions.

・

Up to 8 sets of operational parameters,

including the size of racks and the

number of test tubes, may be

memorized in the battery back-up

protected files.

・

An RS-232C interface

(Cat. No. 204-09079)

and a GP-IB interface

(Cat. No. 204-09155)

are optionally available to allow an

external computer to control the ASC-

5 directly.

・

Up to 100 test tubes may be set

together on the rack.

R928-08 Photomultiplier

Tube

(Cat. No. 200-75021)

・

Replacing the standard photomultiplier

tube of the RF-1501 with this tube

extends the measuring wavelength

range to 900 nm.

Sipper Unit 1500

(Cat. No. 206-69720)

・

Aspirates solution samples one after

another, using a peristaltic pump

driven by a stepping motor, to be

measured successively.

・

Specifications

Flow-thru cell: Square flow-thru cell

made of fused silica.

Cell capacity: 120

μ

L

Aspiration speed: FAST, MEDIUM,

and SLOW.

Minimum sample volume: 2 mL

(Less than 1% carry-over)

Linked operation with the ASC-5

Auto Sampler possible.

・

Standard accessories

Drain tank

Tygon tube, 2.5 meters long, for pump

connection

ASC-5 connecting cable

・

Options and Supplies

Solenoid Valve Unit with wetted

parts made of Teflon

(Cat. No. 206-69824)

SWA-2 Sample Waste Unit

(Cat. No. 204-29230)

Note:The tubing of the standard

peristaltic pump is not resistant enough

against strong acids, strong alkalis, and

ester solutions; use of the above

mentioned Solenoid Valve Unit and

SWA-2 is recommended.

Tygon tube for pump

(Cat. No. 200-84523-04)

NTT-2200P Constant-

Temperature Water

Circulator

(Cat. No. 208-97263)

・

Circulates temperature controlled

water to a constant-temperature cell

holder.

・

Temperature range:

Ambient +5

℃

to +80

℃

・

Temperature control precision:

±

0.05

℃

∼

・

Max. pumping rate:

27/31 L/min, 9.5/13 m (50/60 Hz)

・

External circulation nozzle:

10.5 mm OD (both outlet and return)

・

Tank capacity: About 10 L

(9 L during use)

・

Safety feature:

Detection of over-temperature of

Upper or Lower limits, Detection of

heater wire malfunction, Protection of

heating too few circulating water,

Detection of sensor malfunction,

Independent over teat protection,

Over current circuit protector

・

Standard accessories:

Lid with handles, Rubber hose (4m),

Hose clamps (4pc.), Instruction

manual

・

Dimensions:270W

×

560H

×

400D

(mm)

・

Power requirements:

100 VAC, 1250 VA,with 1.7 m power

cord and grounded plug

10

1 2 ... 5 6 7 8 9 10 11 12

Comentarios a estos manuales

Sin comentarios